How did you commission it? If I remember correctly off the top off my head If this doesnt turn boiler on and off then there is a fault with the wiring or the receiver is faulty -hold the 2 buttons down for a few seconds untill the red light flashes, which then sends out a signal. Ive had to replace a few of these. Hope this helps. Click to expand
|Genre:||Health and Food|
|Published (Last):||24 January 2009|
|PDF File Size:||20.61 Mb|
|ePub File Size:||19.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Description Questions? If it is the model with the receiver built into the boiler, then you need HCO Code 04D04 Q: Can I use this unit to control individual thermostats in different room zones at the required set temp.
A: No. This is just a plain wireless thermostat. The RC1 thermostat has just broken and I think is no longer made. Can I buy an alternative and use it with my WR1 receiver, or do I have to buy a new thermostat and receiver?
A: Yes, this one would be suitable. It will pair to your existing receiver, however due to the age of it, I would recommend replacing both parts. The new receiver will clip onto the backplate of the WR1 with no wiring changes. Q: We had a British Gas Boiler believe re-branded Worcester fitted approx 4 years ago, no issues until now when we have hot water but intermittent heating despite the flame icon being on at the transmitter unit.
The tranmitter is a British Gas RC1 Plus can you advise whether this transmitter will be compatible with the existing receiver. A: Yes it would. Q: I have a Drayton rf the digistat is broke can I replace with an rf as they use the same receiver Many thanks darren A: Yes, you can. What does it mean by Worcester Receivers must have issue 2 printed on the back of the rec. As yours is a British Gas branded one, not a Worcester branded one then the issue 2 does not apply to you.
Q: I have a horstmann H37XL system controlling heating. This is satisfactory. I have the downstairs control in the wrong room. I want to replace this without rewiring. Can this controller and receiver replace the standard wired thermostat. Can I just rewire the receiver in place of the exiting controller and install the transmitter where I want it. If this is not the best solution can you suggest a solution with another product you have.
Many thanks. A: You will not be able to replace the existing thermostat with the receiver. You will have to install the receiver next to the H37XL. Q: How do you set the correct time on the thermostat? Can I just replace the thermostat and pair this with the receiver in my boiler or do I need to purchase the receiver as well? A: Yes you can. I know the 1RF is a far simpler control but would prefer that.
Thanks A: Yes it will. Also can I use the existing backplate without re-wireing? Yes the new receiver will plug onto the existing backplate with no wiring changes needed. I have read the info about this being a direct replacement as long as it runs on a frequency of mhz. You have referred to the branding being the indicator of this. Can you please confirm where the branding will be displayed so I can ask my mother to check over the telephone? I just want to make sure she is looking in the right place.
Is it just the branding on the front of the thermostat and receiver? Is that right? Thanks in advance.
A: Yes, it is the branding on the front of the units. Yes, if the has the older one with the ACL in an octagon she will need to replace both parts. The heating system was installed 11years ago A: Yes you can. The digital thermostat is not working properly and needs replacing. Will any of your products be compatable? A: This is compatible. Is the receiver a direct replacement for the dialed thermostat? A: No, you will keep the thermostat on the front of the boiler, as it determines how hot the radiators get.
This 1RF thermostat will switch off the boiler when the house is up to temperature. So you will need to use both thermostats together for best effect. Q: I have a drayton scr and thermostat. Do we have to replace the scr and thermostat or just the thermostat.
Also if replacing the scr could I just replace the front and reuse the back plate? A: Yes you can replace just the thermostat. If you did want to replace the SCR you can reuse the back plate. Q: I have a Drayton RF1 wireless room stat and scr running a vaillant combi boiler. The wireless stat was knocked onto a hard floor and no longer works, even with new batteries.
Is this new stat compatible with the current scr or do I need to replace the stat and the scr? A: Provided it works on mhz please see link in product description , then yes it is. Q: Hi I have an ideal logik combi boiler And at the moment we are controlling The temperature from the front control panel of the boiler.
I have bought the wireless thermostat but could you tell me if it is compatible with my boiler thanks Tom A: Yes it is. The wireless thermostat has stopped working. Do we need to replace both components or can be just get a new thermostat?
Thanks, Viki A: You can replace just the thermostat but depending on the age maybe best to replace both, as a pack is much cheaper. Q: Hi I have a one off these of the same design but it has British Gas in the display window. Regards Martin A: Yes it is.
Q: I have a 6 years old drayton digistat RF1 Now faulty , can you use the same back plate to save rewiring , thank you A: The backplate design has not changed, so the new receiver will simply plug on without any wiring changes.
ACL Drayton Digistat+ 1RF Wireless Digital Thermostat
Drayton Digistat SCR and Digistat R1 room stat not working