So now i activate the alarm on only a 3 digit code and it is working like that. At the moment telephone line seizure occurs, the Telco Tip is momentary connected to earth ground to access dial tone. The system must be in ready mode. If a keypad tamper code is entered then it will be transmitted to the Central Station. Got it, progrm to print.
|Published (Last):||6 June 2007|
|PDF File Size:||14.48 Mb|
|ePub File Size:||6.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
Directly to a single or double gang electrical junction box. Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds. LCD display keypads will indicate the following xxl2t I then fbii code button followed by master codeprlgram user no 3 and then new 4 digit user code.
After this time period, power is restored. System Programming Programming Questions This topic defines the programming questions and the values for each question. We regret any inconvenience this may have caused and appreciate your continued support of FBII products. Trigger 1 must be selected for smoke detector power reset for this feature to active.
Comments to this Manuals Your Name. The system features seven 7 fully programmable zones. If a keypad tamper code is entered then it will be transmitted to the Central Station. A user code is required to disarm the system. Good Day I had a four digit user code, but the last digit was lost.
So now i activate the alarm on only a 3 digit code and it is working like that. The alarm was then activated, without me activating it. Some new features have been added and others have been modified. Page of 93 Go. Question 32, L1 — Bypass Code Sounder Only always enabled Programmable Dialer Attempts: Quick Arming allows arming the system without entry of a user code and will report as user This will be used by the CS downloading computer to determine the proper account information to download to this subscriber.
The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected. Programming Questions This topic defines the programming questions and the values for each question. If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode. Secure keypad to double-gang box as shown x2t graphic at left. Select the desired location between wall studs for mounting the keypad. Page 70 Section 6 — System Programming When programming the English zone descriptors, use the following techniques to program the characters: The following is a quick comparison.
Most 10 Related.
FBI XL2T PROGRAM PDF
Tojazragore Next, enter the desired account number each digit followed by the key. Pprogram the digit from the table below. Secure keypad to double-gang box as shown in graphic at left. The keypads can be surface mounted or flush mounted as described below. Section 5 — System Operations If a user code is not required to set the time, then enter: Section 5 — System Operations 4. I then pressed code button followed by master codethen user no 3 and then new 4 digit user code.
Enter text from picture: To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger. The door of the metal cabinet may be removed to make it easier to install the control panel. The auto arm time represents the time of day that the area will automatically arm if it is not already armed. Trigger 1 must be selected for smoke detector power reset for this feature to active.
Shajin The restore code will also be reported if the system is disarmed during an alarm. I pressed the code button ready light did not flashthen pressed both 7 and 9 at same time, fni reset master code to There are 36 total questions, with multiple data entry locations. Once deleted their values will be null. Question 32, L1 — Bypass Code The keypads can be surface mounted or flush mounted as described below.
Nikogis Secure keypad to double-gang box as shown in graphic at left. Question 32, L1 — Bypass Code Directly to a single or double gang electrical junction box. Create an opening and mount a standard double-gang box. How can i change or get rid of this 3 digit code.