Arashishura This can be used to increase the speed of plotting. If the text lines are to be redrawn on the zoom plot, they are drawn at the same plot co-ordinate positions as when they were created. Number of Columns in first file 7. However, even as a novice, you can very successfully use the program if you are willing to invest some time to read the manual, and if you can avoid being intimidated at first by the large set of commands and relatively long learning curve. Gets the Meta-Cornmand-File name from the user.
|Published (Last):||11 February 2009|
|PDF File Size:||3.6 Mb|
|ePub File Size:||2.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Note that the line colour will only apply to colour terminals and colour plotters. Re-start program for new plot 2. Sets up the tick mark parameters. If any error occurs while reading the data the user will be notifed and the file line in question will be displayed. Time at start of plot sec. Positions Text Lines 5. They arc only applicable to colour terminals and colour plotters. If a legend has previously been created in a non-zoom plot the user will be given the following options: Labels will be drawn in a program-defined size.
Director, Aeronautical Research Laboratory, P. More than one MCF can be requested if the manusl requires output to more than one output device. Enters one integer number from user. If a very long label exceds the length of the plot the program will reduce the character sizing until the label is small enough to fit inside the plot window.
Determines the length of the entered string. The drawing options menu is as shown below. Get number of lines to skip between reading data from file. If the plots are only being displayed via meta-files the aspect ratio will be unity.
The numeric labels can be drawn inside or outside the plot box. Name of first data file 5. Terminal Type VT 3. GENPLOT is a generic plotting package that is particularly useful for presenting and analyzing scientific research data. Search the history of over billion web pages on the Internet. Column number to plot on Y-axis This file contains the data file name, the number of columns in the data file, the line number to start reading data file, and i the line number to stop reading the data file.
If this is set as zero the maximum available display area will be used. The Top-Left-Corncr of the legend box is positioned by the user. Draws a triangular-shaped marker at the specified position on the plot. It is essentually menu-driven, with validity checks and error recovery on entered selections. Displays program exit message. Line number to start reading in 2nd file The plot labels were set as follows: Number of lines to skip in 1st file TOP 10 Related.
GENPLOT - By Michael O. Thompson ([email protected])
Goshura Line number to end reading in 2nd file Naturally some accuracy will be lost since not all the available data is being plotted. Genpkot user may enter data for each line on the plot by one of four methods: A user may make X-Y graphs no pie charts allowed — this is for scientists, not managersplot data and simulation curves, transform the data in various ways, and later spruce up the plots for publication. The default is to draw the box. The tick spacing can be explicitly set by the user or left for the program to determine.
GENPLOT MANUAL PDF
Maull If simple command line prompts bring chills and tingles to your spine, this program is probably not for you. This file can be in the user current directory or in a sub-directory of the current directory. However the user may wish to extend these to allow a margin between the lines gfnplot the plot edge or simply to round the limits to a more acceptable value. The default is to draw the line. More than one MCF can be requested if the user requires output to more than one output device. Makes a zoom plot of a selected area of the plot. Clips the data used for zoom plots venplot ensure only data within the plot box is displayed.
Plots can be sent to driver- supported plotters for hardcopy output. Input Default value file 3. Plotting Options for Line nn 0. The exceptions to this are the plot limits and plot labels. The tick spacing can be explicitly set by the user or left for the program to determine. If the user selects a terminal type in the start-up program for which a bound version does not exist the user will be notified.
Jugar This document is divided into two parts; a user guide, and a reference manual. This can be used to increase the speed of plotting. Geplot version for that terminal type will then have to be created and made available to the users. Plots can be sent to driver- supported plotters for hardcopy output. Default settings for these options are set on program initialisation which give reasonable un-labelled plots. Number of data to skip in 1st file The tick spacing can be explicitly set by the user or left for the program to determine.